What is the maximum misalignment angle this 50mm bore spherical roller bearing can accommodate?

This bearing can accommodate up to 2 degrees of misalignment between the inner and outer rings. This self-aligning capability is due to the spherical raceway of the outer ring, which allows the roller assembly to tilt. In practice, this means the bearing can compensate for shaft deflection or mounting errors without generating excessive internal stresses. For applications with higher misalignment, consider using a bearing with a larger misalignment angle or a different bearing type. Always ensure that the misalignment does not exceed the specified limit to avoid reduced bearing life.

How do I install this spherical roller bearing correctly to ensure optimal performance?

Installation should follow these steps: First, clean the shaft and housing, and check for burrs or damage. Mount the bearing using an induction heater or oil bath, heating it to 80-100°C (never exceed 120°C). For tapered bore bearings, use a lock nut and adapter sleeve to achieve the required interference fit. After mounting, verify alignment by rotating the shaft; misalignment should not exceed 2 degrees. Lubricate the bearing with the recommended grease or oil (e.g., lithium complex grease) filling 30-50% of the free space. Finally, run the machine at low speed for a few minutes and check for abnormal noise or vibration.

What is the expected service life of this bearing under typical operating conditions?

The service life depends on load, speed, lubrication, and environment. Under normal conditions with proper lubrication and alignment, the basic rating life (L10) can be calculated using the dynamic load rating of 85kN. For example, if the equivalent dynamic load is 20kN and speed is 1000 rpm, the L10 life is approximately 15,000 hours. However, actual life may vary; factors like contamination, inadequate lubrication, or excessive misalignment can reduce life significantly. Regular maintenance, including lubrication replenishment and vibration monitoring, can help achieve or exceed the calculated life.

Spherical Roller Bearing

50mm Bore Spherical Roller Bearing for Heavy Radial Loads and Misalignment

The 50mm bore spherical roller bearing (90mm OD, 23mm width) is a self-aligning rolling element bearing designed to handle heavy radial loads and moderate axial loads in both directions. Its double-row spherical rollers accommodate misalignment up to 2 degrees, making it ideal for applications where shaft deflection or mounting inaccuracies are present.

Width

23mm

Dynamic Load Rating

85kN

Static Load Rating

120kN

Max Speed

4500 rpm

Request A Quote Send E-mail

How Does the 50mm Bore Spherical Roller Bearing Handle Misalignment and Heavy Loads?

The 50mm bore spherical roller bearing (90mm outer diameter, 23mm width) is engineered with two rows of symmetrical spherical rollers that run on a common spherical raceway in the outer ring. This design allows the bearing to self-align under shaft deflection or misalignment up to 2 degrees, preventing edge loading and premature failure. The bearing's dynamic load rating of 85kN and static load rating of 120kN make it capable of carrying heavy radial loads and moderate axial loads in both directions. The machined brass cage ensures reliable roller guidance and withstands high temperatures up to 200°C, while the P6 precision grade guarantees low vibration and noise. Typical applications include conveyor pulleys, crushers, vibrating screens, and gearboxes where misalignment and heavy loads are common.

In industrial settings, the 50mm bore spherical roller bearing addresses specific pain points: shaft deflection in long shafts, mounting errors in welded housings, and thermal expansion in high-temperature environments. For instance, in a conveyor pulley application, the bearing compensates for up to 2 degrees of misalignment caused by belt tension, reducing maintenance downtime. The bearing's high load capacity allows for smaller shaft diameters, saving space and cost. Compared to deep groove ball bearings, this spherical roller bearing offers 2-3 times higher radial load capacity, making it suitable for heavy-duty applications. The brass cage resists wear and deformation, ensuring long service life even under shock loads.

When compared to other spherical roller bearings in the series, the 50mm bore variant is optimized for medium-duty applications where space is limited but load requirements are high. Its 23mm width provides a balance between load capacity and compactness, making it ideal for gearboxes and pumps where axial space is constrained. The bearing's self-aligning feature eliminates the need for precise shaft alignment, reducing installation time and cost. With a limiting speed of 4500 rpm, it is suitable for moderate-speed applications. The bearing is also available with tapered bore (K suffix) for adapter sleeve mounting, offering flexibility in shaft design.

Self-aligning capability up to 2 degrees reduces misalignment-related failures and extends bearing life by up to 30% compared to rigid bearings.
Dynamic load rating of 85kN and static load rating of 120kN provide high load capacity for heavy radial and axial loads.
Machined brass cage withstands temperatures up to 200°C and provides reliable roller guidance under shock loads.
P6 precision grade ensures low vibration and noise, meeting ISO 492 tolerance standards.

Core Technical Features and Quantified Advantages

STEP 1

Self-Aligning Design with 2-Degree Misalignment Tolerance

The spherical outer ring raceway allows the inner ring and roller assembly to tilt up to 2 degrees relative to the outer ring, compensating for shaft deflection and mounting errors. This reduces edge stresses and prevents premature fatigue. In applications like conveyor pulleys, this feature eliminates the need for precise alignment, cutting installation time by 40% and extending bearing life by up to 30% compared to non-self-aligning bearings.

STEP 2

High Load Capacity: 85kN Dynamic and 120kN Static Ratings

With two rows of spherical rollers, the bearing distributes load over a larger contact area, achieving a dynamic load rating of 85kN and static load rating of 120kN. This allows it to carry heavy radial loads and moderate axial loads in both directions. For example, in a crusher application, the bearing can withstand shock loads up to 120kN without permanent deformation, ensuring reliable operation in harsh environments.

STEP 3

Machined Brass Cage for High-Temperature and Shock Load Applications

The machined brass cage (CuZn39Pb2) provides high strength and resistance to wear, deformation, and high temperatures up to 200°C. It guides the rollers precisely, reducing friction and heat generation. Compared to steel cages, brass cages offer better performance under shock loads and vibration, making them ideal for applications like vibrating screens and crushers where reliability is critical.

STEP 4

P6 Precision Grade for Low Vibration and Noise

Manufactured to P6 precision grade according to ISO 492, the bearing features tight tolerances on dimensions and runout, ensuring smooth operation with low vibration and noise. This is essential for applications such as electric motors and gearboxes where noise and vibration must be minimized. The P6 grade also reduces bearing friction, leading to lower operating temperatures and longer grease life.